Baldor PC SEries Instrukcja Operatora Strona 1

OPERATOR'S MA

ENGINE INFORMATION This operator's manual only covers basic day to day engine operating instructions. However, the engine manufacturer's ma

MAINTENANCE MAINTENANCE SHOULD ONLY BE PERFORMED ON THE GENERATOR SET AFTER THE ENGINE HAS STOPPED AND THE GENERATOR SET HAS COOLED DOWN. THE BATTERY

ADJUSTMENTS: √ The engine should be checked for proper speed setting(s). √ Adjust the engine speed to 3720 RPM's (62 Hz) with no load applie

As an alternative to draining the fuel from a gasoline engine, you can add a fuel stabilizer, such as "STA-BIL" to minimize the fo

ORDERING PARTS When Generator repair parts are needed, they may be obtained by calling the Customer Services Department at Baldor Generators or the

OPERATION PRIOR TO STARTING THE UNIT: 1. Locate and set up the generator set in an open, dry, well ventilated and reasonably level location.

3. Pull lightly on the recoil grip until you feel significant resistance, then pull sharply. Do not allow the recoil rope to 'snap'

SIMPLE TROUBLESHOOTING Listed below are the more simple solutions to some of the more common problems that are reported to the Service Department at

5. Loss of residual magnetism. Loss of residual magnetism will not allow the generator's excitation system to build up and thus the generator s

CONTROL PANEL For the PC25B and the PC30H A = CIRCUITBREAKER. This circuit breaker provides

FORWARD This manual contains the information you need to safely and efficiently operate y

CONTROL PANEL MAH30 and the MAV30 Units A = NEMA 515R GFCI DUPLEX. This receptacle is a ground

CONTROL PANEL PC40H, PC40B and PC50H Units A = NEMA 515R GFCI DUPLEX. This receptacle is a grou

CONTROL PANEL PC60H A = NEMA 515R GFCI DUPLEX. This receptacle is a ground fault circuit

CONTROL PANEL PC90VE A = NEMA 515R GFCI DUPLEX. This receptacle is a ground fault circuit

Generator End Componentry For PC25B, PC30H, MAV30, and MAH30 Generator Sets - 247 -

PARTS BREAKDOWN FOR PC25B & PC30H REF LETTER OLD PART # NEW PART # DESCRIPTION A 46.10025D 61SA0019A02SP 

Generator End Componentry For PC40H, PC40B, PC50H, and PC90VE Generator Sets - 269 -

PARTS BREAKDOWN FOR PC40H, PC40B, PC50H, PC60H, and PC90VE Units: REF LETTER OLD PART # NEW PART # DESCRIPTION A Consult Factory

CONNECTION DIAGRAM PC30H - 21-

Connection Diagram MAH30 & MAV30 - 22 -

♦ Place protective covers and guards over the rotating parts, if rotating parts such as the drive shaft, pulley, belt, etc. are left expo

Connection Diagram PC40H, PC40B & PC50H - 23 -

Connection Diagram PC60H - 24 -

Connection Diagram PC90VE - 55 -

LIMITED WARRANTY Unless otherwise provided, Baldor generators are warranted against defects in Baldor workmanship and materials for a period of time

WARRANTY PERIOD GENERATOR SERIES Labor* Parts Portable Products (Premier, PowerChief, DG Series, K Series) 1 Year 3 Years Towable Products (TS) 1 Y

Limitations: Baldor Generators is not responsible for the repair of generators required because of normal wear, accident, misuse, abuse, improper in

CALIFORNIA PROPOSITION 65 WARNING Engine exhaust from this product contains chemicals known to the state of C

Service is just a phone call away: 800-872-7697 www.baldor.com/products/generators.asp 3815 Oregon Street Oshkos

♦ Know how to stop the engine quickly and understand the operation of all controls. ♦ Never permit anyone to operate the generator set without pr

♦ Always treat the electrical circuits as if they were energized. ♦ Disconnect all leads plugged into the unit Prior to working on it. ♦ Have the

○ ○ ○ ○ FOR GASOLINE OR DIESEL POWERED GENERATOR SETS ○ ○ ○ ○ ♦ Check all fuel supply piping and their connections on a monthly

TABLE OF CONTENTS SECTION PAGE Basic Location Information…………………………………………………………………………………………….1 Basic Connection Information…………

LOCATION For best service from your portable generator set there are several factors which should be taken into consideration when choosing the best

CONNECTIONS WIRING: Use sufficiently large insulated wire to connect the generator set to the load. The gauge of the wire will depend largely on t